Reducing Mould Risk during the Building Design Stage: Case Studies in South-East China
Main Article Content
Abstract
Indoor mould is usually discussed for the building operation phase rather than the design stage. Moreover, the majority of existing studies were conducted by mechanical engineers rather than architects, who typically have a broader view of the whole project. The purpose of this article is to obtain a quantitative mould risk scenario across the Yangtze River Delta in China and make a matrix including all the possible design options to reduce the mould risk. A series of software is utilised to simulate the mould risk in three main cities across that region. Simulation results confirm high mould risk in all selected cities and the mould growth rates in different orientations match the Wind-Driven Rain diagram. After the simulation, all factors that can be tuned for the mould prevention were analysed. It is found that only humidity and substrate (material of finishing layer) characteristics can be practically controlled for mould avoidance. Meanwhile, the development design stage is the essential design phase while the envelope is the most crucial building element for mould prevention.
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) (2012). ASHRAE Position Document on Limiting Indoor Mold and Dampness in Buildings. Georgia, USA: ASHRAE.
–––––. (2009). Indoor Air Quality Guide. Georgia, USA: ASHRAE.
Baidu.com (2016). 梅雨季节 [Plum season]. Available at: http://baike.baidu.com/item/梅雨季节/32325 [Accessed on 15 May 2020].
Chang, J.C.S., Foarde, K.K. and VanOsdell, D.W. (1996). Assessment of fungal (Penicillium chrysogenum) growth on three HVAC duct materials. Environment International, 22(4): 425–431. https://doi.org/10.1016/0160-4120(96)00030-X.
Chen, W.J., Claridge, D.E., Rohrs, C. and Liao, J. (2016). Modeling to predict positive pressurization required to control mold growth from infiltration in buildings in a hot and humid climate. Building and Environment, 104: 102–113. https://doi.org/10.1016/j.buildenv.2016.05.001.
Elisa, G. (2013). Nearly Zero Energy Buildings and Proliferation of Microorganisms. Cham, Switzerland: Springer.
Fantucci, S., Isaia, F., Serra, V. and Dutto, M. (2017). Insulating coat to prevent mold growth in thermal bridges. Energy Procedia, 134: 414–422. https://doi.org/10.1016/j.egypro.2017.09.591.
Fraunhofer Building Innovation (2017). WUFI® BIO. Available at: https://wufi.de/en/2017/03/31/wufi-bio/ [Accessed on 15 May 2020].
General Office of the State Council (2007). 国务院办公厅关于严格执行 公共建筑空 调温度控制标准的通知 [Notification of Temperature Control Standards for Air Conditioning in Public Buildings]. Beijing: General Office of the State Council. Available at: http://www.gov.cn/xxgk/pub/govpublic/mrlm/200803/t20080 328_32576.html [Accessed on 15 May 2020].
Häglund, M., Isaksson, T. and Thelandersson, S. (2010). Onset of mould growth: The effect of climate variability and different geographic locations. IRG 10–20446. Paper presented at the Conference IRG 41. Biarritz, France, 9–13 May.
Harriman, L. and Neil, L. (2006). California Builder's Guide to Reduce Mold Risk. Des Plaines, CA: Gas Technology Institute.
Hens, H. (2003). Mold in dwellings: Field studies in a moderate climate. Proceedings of the 24th AIVC Conference and BETEC Conference, Ventilation, Humidity Control and Energy. Washington DC: Air Infiltration and Ventilation Centre (AIVC), 12–14. Available at: https://bwk.kuleuven.be/bwf/projects/annex41/protected/data/KUL%20Apr%202006%20Paper%20A41-T4-B-06-5.pdf [Accessed on 15 May 2020]. –
––––. (1992). IEA Annex 14: Condensation and energy. Journal of Thermal Insulation, 15(3): 261–273. https://doi.org/10.1177/109719639201500307.
Hens, H.L.S.C. (1999). Fungal defacement in buildings: A performance related approach. HVAC&R Research, 5(3): 265–280. https://doi.org/10.1080/10789669.1999.10391237.
Hyvärinen, A., Meklin, T., Vepsäläinen, A. and Nevalainen, A. (2002). Fungi and actinobacteria in moisture-damaged building materials: Concentrations and diversity. International Biodeterioration and Biodegradation, 49(1): 27–37. https://doi.org/10.1016/S0964-8305(01)00103-2.
Jiangsu Provincial Office for Construction Engineering Standards (2006). HR 保温装饰 板外保温系统 [External Insulation System with HR Decorative Insulation Board]. Nanjing: Jiangsu Provincial Office for Construction Engineering Standards. Available at: http://183.61.19.162/zdoc/苏JT16-2006(五)建筑外保温构造图集(五)HR保温装饰板外保温系统.pdf [Accessed on 15 May 2020].
Johansson, P. (2014). Determination of the critical moisture level for mould growth on building materials. PhD diss., Lund University.
Johansson, S., Wadsö, L. and Sandin, K. (2010). Estimation of mould growth levels on rendered façades based on surface relative humidity and surface temperature measurements. Building and Environment, 45(5): 1153–1160. https://doi.org/10.1016/j.buildenv.2009.10.022.
–––––. (2005). Microbial growth on buildings facades with thin rendering on thermal insulation. In 7th Nordic Building Physics Symposium in Reykjavik. Reykjavik, Iceland: Division of Building Materials, Lund University.
Karagiozis, A. and Hadjisophocleous, G. (1995). Wind-driven rain on high-rise buildings. Buildings VI Proceedings. Oak Ridge, TN: Oak Ridge National Laboratory (ORNL), 399–406. Available at: https://web.ornl.gov/sci/buildings/conf-archive/1995%20B6%20papers/044_Karagiozis.pdf [Accessed on 15 May 2020].
Khan, A.A.H. and Karuppayil, S.M. (2012). Fungal pollution of indoor environments and its management. Saudi Journal of Biological Sciences, 19(4): 405–426. https://doi.org/10.1016/j.sjbs.2012.06.002.
Ministry of Housing and Urban-Rural Development (MOHURD) (2016). 建筑工程设计文 件编制深度规定 [Regulation on the Depth of Construction Engineering Design Documents]. Beijing: MOHURD. Available at: http://www.mohurd.gov.cn/wjfb/201612/t20161201_229701.html [Accessed on 15 May 2020].
–––––. (2010). 夏热冬冷地区居住建筑节能设计标准 [Design Standard for Energy Efficiency of Residential Buildings in Hot Summer and Cold Winter Zone]. Beijing: MOHURD. Available at: http://www.jianbiaoku.com/webarbs/book/412/2592432.shtml [Accessed on 15 May 2020].
Mlakar, J. and Štrancar, J. (2013). Temperature and humidity profiles in passive-house building blocks. Building and Environment, 60: 185–193. https://doi.org/10.1016/j.buildenv.2012.11.018.
Møller, E.B., Andersen, B., Rode, C. and Peuhkuri, R. (2017). Conditions for mould growth on typical interior surfaces. Energy Procedia, 132: 171–176. https://doi.org/10.1016/j.egypro.2017.09.680.
Moon, H. and Augenbroe, G. (2004). Future research needs for mold growth risk analysis. In CIB World Building Congress 2004, Building for the Future Building for the Future. Ontario, Canada: National Research Council of Canada, 1–10. Available at: https://www.irbnet.de/daten/iconda/CIB1772.pdf [Accessed on 15 May 2020].
Moon, H.J. and Augenbroe, G. (2003). Evaluation of hygrothermal models for mold growth avoidance prediction. Paper presented at the Eighth International IBPSA Conference. Eindhoven, Netherlands, 11–14 August.
Nunez, M. and Hammer, H. (2014). Microbial specialists in below-grade foundation walls in Scandinavia. Indoor Air, 24(5): 543–551. https://doi.org/10.1111/ina.12095.
Orlik-Kozdo?, B. and Steidl, T. (2017). Impact of internal insulation on the hygrothermal performance of brick wall. Journal of Building Physics, 41(2): 120–134. https://doi.org/10.1177/1744259116671322.
Ritschkoff, A.C., Viitanen, H. and Koskela, K. (2000). The response of building materials to the mould exposure at different response conditions. In Healthy Buildings 2000: Proceedings; Vol. 1, Exposure, Human Responses and Building Investigations. Helsinki: SIY Indoor Air Information Oy, 317–322.
Rose, W.B. (2005). Water in Buildings: An architect's Guide to Moisture and Mold. Hoboken, NJ: Wiley.
Sedlbauer, K. (2001a). Prediction of Mould Fungus Formation on the Surface of/and inside Building Components. München, Germany: Fraunhofer Institute. Available at: http://www.ibp.fraunhofer.de/content/dam/ibp/en/documents/ks_dissertation_etcm1021-30729.pdf [Accessed on 15 May 2020].
–––––. (2001b). Vorhersage von schimmelpilzbildung auf und in bauteilen [Prediction of mold formation on and in construction units]. PhD diss., Universität Stuttgart.
Shanghai Commission of Urban and Rural Construction and Transportation (2013). 装配整体式混凝土住宅构造图集 [Atlas of the Assembled Monolithic Residential Structures]. Shanghai: Shanghai Commission of Urban and Rural Construction and Transportation. Available at: https://wenku.baidu.com/view/3f08214f998fcc22bcd10dca.html [Accessed on 15 May 2020].
Trechsel, H. and Bomberg, M.T. (2010). Moisture Control in Buildings: The Key Factor in Mold Prevention. 2nd Ed. Philadelphia, PA: ASTM International. United States Environmental Protection Agency (US EPA) (2013). Moisture Control Guidance for Building Design, Construction and Maintenance. Washington DC: US EPA.
–––––. (2012). A Brief Guide to Mold, Moisture and Your Home. Washington DC: US EPA. Vereecken, E. and Roels, S. (2012). Review of mould prediction models and their influence on mould risk evaluation. Building and Environment, 51(April): 296– 310. https://doi.org/10.1016/j.buildenv.2011.11.003.
Viitanen, H. and Ritschkoff, A. (1991). Mould Growth in Pine and Spruce Sapwood in Relation to Air Humidity and Temperature. Uppsala, Sweden: Swedish University of Agricultural Sciences.
Viitanen, H., Vinha, J., Salminen, K., Ojanen, T., Peuhkuri, R., Paajanen, L. and Lahdesmaki, K. (2010). Moisture and bio-deterioration risk of building materials and structures. Journal of Building Physics, 33(3): 201–224. https://doi.org/10.1177/1744259109343511.
Wang, Z. (2007). 机械通风是解决中国住宅室内通风问题的最佳方法 [Mechanical ventilation is the best way to solve the ventilation problem in Chinese residential buildings]. In 2007年中日可持续发展建筑技术与产品交流会论文集 [Proceedings of the 2007 China-Japan Sustainable Construction Technology and Product Exchange Conference]. Beijing: China Academy of Building Research. Available at: http://www.wanfangdata.com.cn/details/detail.do?_type=conference&id=6575840 [Accessed on 15 May 2020].
Warsco, K. and Lindsey, P.F. (2003). Proactive approaches for mold-free interior environments. Archives of Environmental Health, 58(8): 512–22. https://doi.org/10.3200/AEOH.58.8.512-522.
Wei, X. (2016). 上海市居住建筑室内墙体表面霉菌生长调研 [Study on mould growth in dwelling building of Shanghai]. 建筑热能通风空调 [Building Energy and Environment], 35(1): 27–30.
Zhejiang Provincial Department of Housing and Urban-Rural Development (2013). 轻质混凝土砖墙体节能与结构一体化构造 [Integral Structure and Energy Saving of Lightweight Concrete Block Wall]. 1st Ed. Hangzhou: Zhejiang Gongshang University Press. Available at: https://ebook.chinabuilding.com.cn/zbooklib/bookpdf/probation?SiteID=1&bookID=103828 [Accessed on 15 May 2020].